Vektr's Opel And + 1. Maintenance instruction + 1.1 Maintenance + 2. Engine + 3. Repair of DOHC engines + 4. Repair of the diesel engine + 5. Cooling system + 6. Fuel system + 7. The fuel and exhaust system of models with system of injection of fuel + 8. Exhaust system and system of decrease in toxicity of exhaust gases + 9. Fuel systems of the diesel engine - 10. Engine electrical systems 10.2. General information 10.3. System of ignition 10.4. Check of system of ignition 10.5. Rules of care of the accumulator 10.6. Check of the accumulator 10.7. Accumulator charging 10.8. Accumulator 10.9. System of charging 10:10. Generator 10:11. Driving belt of the generator 10:12. Removal and installation of the generator 10:13. Generator brushes 10:14. BOSCH generator 10:15. Small-sized DELCO-REMY generator 10:16. System of start of the engine 10:17. Starter 10:18. Removal and installation of a starter 10:19. Ignition coil 10:20. Cover and rotor of the distributor of ignition 10:21. Distributor of ignition (SOHC model) 10:22. Distributor of ignition (DOHC model) + 10:23. Repair of the distributor of ignition 10:24. Check and adjustment of a corner of an advancing of ignition 10:25. Fine tuning of the moment of ignition under the used fuel grade 10:26. Electronic modules 10:27. MSTS-i elements 10:28. Sensor of speed/provision of a bent shaft (model of 1,8 l) 10:29. Motronic system elements 10:30. Sensor of a detonation (DOHC model) 10:31. DIS module 10:32. Sensor of phases of the camshaft (C20 XE engine) 10:33. System of prestarting heating 10:34. Glow plugs + 11. Transmission + 12. Mechanical transmission + 13. Automatic transmission + 14. Power shafts + 15. Brake system + 16. Suspension bracket + 17. Body + 18. Electric equipment + 19. Check of malfunctions
|
Removal
MODELS 14 NV I 16 SV
Removal of a cover of the distributor of ignition on model 1,6 l (BOSCH distributor)
Removal of a cover of the distributor of ignition on model 1,6 l (LUCAS distributor)
Removal of a rotor of the distributor and plastic filter on model 1,6 l (BOSCH distributor)
PERFORMANCE ORDER |
1. Remove a weight wire from the accumulator. |
2. Mark and disconnect high-voltage wires from a cover of the distributor of ignition and spark plugs, at the same time pull not for a wire, and for a candle tip. Also remove the high-voltage wire connecting the ignition coil to an ignition distributor cover. |
3. On the BOSCH distributor, using a screw-driver edge, remove two spring brackets and uncover the ignition distributor. On the LUCAS distributor unscrew two screws and uncover the ignition distributor (see rice. Removal of a cover of the distributor of ignition on model 1,6 l (BOSCH distributor), Removal of a cover of the distributor of ignition on model 1,6 l (LUCAS distributor)). |
4. Having pulled, remove a distributor rotor from a shaft. |
5. On BOSCH ignition distributor for access to distributor elements, having pulled, remove the plastic filter from a distributor shaft (see rice. Removal of a rotor of the distributor and plastic filter on model 1,6 l (BOSCH distributor)). |
|
OTHER MODELS
Unscrewing of the screw of fastening of a cover of the distributor of ignition on model of 2,0 l
Removal of the plastic screen from the ignition distributor case on model of 2,0 l
Unscrewing of screws of fastening of a rotor of the distributor of ignition
Removal of a rotor of the distributor of ignition on model of 2,0 l
PERFORMANCE ORDER |
1. Remove a weight wire from the accumulator. |
2. Mark and disconnect high-voltage wires from a cover of the distributor of ignition and spark plugs, at the same time pull not for a wire, and for a candle tip. Also remove the high-voltage wire connecting the ignition coil to an ignition distributor cover. |
3. On the DOHC models except X20 XEV unscrew two bolts and uncover spark plugs a cover of a head of the block of cylinders. |
4. Unscrew three screws and uncover the ignition distributor (see rice. Unscrewing of the screw of fastening of a cover of the distributor of ignition on model of 2,0 l). |
5. Take the plastic screen from the ignition distributor case. On perimeter of the plastic screen the sealing ring is established. At removal of the plastic screen do not damage an ignition distributor rotor (see rice. Removal of the plastic screen from the ignition distributor case on model of 2,0 l). |
6. Using a six-sided key, unscrew two screws and remove an ignition distributor rotor, at the same time the metal nave of a rotor has to remain in the ignition distributor case (see rice. Unscrewing of screws of fastening of a rotor of the distributor of ignition, Removal of a rotor of the distributor of ignition on model of 2,0 l). |
7. Check a condition of a sealing ring on the plastic screen and, if necessary, replace it. |
|
Installation
PERFORMANCE ORDER |
1. Installation is made in the sequence, the return to removal. The rotor of the distributor of ignition can be established only in one situation. If necessary turn a metal nave of a rotor so that openings under the screw were combined with openings in a rotor of the distributor and distributive to a shaft. Check correctness of connection of high-voltage wires. |
|
|
|