Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
- 10. Engine electrical systems
   10.2. General information
   10.3. System of ignition
   10.4. Check of system of ignition
   10.5. Rules of care of the accumulator
   10.6. Check of the accumulator
   10.7. Accumulator charging
   10.8. Accumulator
   10.9. System of charging
   10:10. Generator
   10:11. Driving belt of the generator
   10:12. Removal and installation of the generator
   10:13. Generator brushes
   10:14. BOSCH generator
   10:15. Small-sized DELCO-REMY generator
   10:16. System of start of the engine
   10:17. Starter
   10:18. Removal and installation of a starter
   10:19. Ignition coil
   10:20. Cover and rotor of the distributor of ignition
   10:21. Distributor of ignition (SOHC model)
   10:22. Distributor of ignition (DOHC model)
   + 10:23. Repair of the distributor of ignition
   10:24. Check and adjustment of a corner of an advancing of ignition
   10:25. Fine tuning of the moment of ignition under the used fuel grade
   10:26. Electronic modules
   10:27. MSTS-i elements
   10:28. Sensor of speed/provision of a bent shaft (model of 1,8 l)
   10:29. Motronic system elements
   10:30. Sensor of a detonation (DOHC model)
   10:31. DIS module
   10:32. Sensor of phases of the camshaft (C20 XE engine)
   10:33. System of prestarting heating
   10:34. Glow plugs
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


10:28. Sensor of speed/provision of a bent shaft (model of 1,8 l)

Removal

Unscrewing of a bolt of fastening of the sensor of speed/provision of a bent shaft on models of 1,8 l

Check of a condition of a sealing ring of the sensor of speed/provision of a bent shaft on model of 1,8 l

PERFORMANCE ORDER
1. The sensor is located in the lower part of the block of cylinders behind the oil pump from a final collector.
2. Remove a weight wire from the accumulator.
3. Release brackets of fixing of an external casing of a gear belt and disconnect from it a sensor electrical wiring.
4. Note an arrangement and disconnect an electrical wiring from the sensor.
5. Unscrew a bolt of fastening of the sensor and take the sensor from the block of cylinders (see rice. Unscrewing of a bolt of fastening of the sensor of speed/provision of a bent shaft on models of 1,8 l).
6. Check a condition of a sealing ring of the sensor and, if necessary, replace it (see rice. Check of a condition of a sealing ring of the sensor of speed/provision of a bent shaft on model of 1,8 l).

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal.
2. Arrange a sensor electrical wiring as appropriate on a casing of a gear belt.