Vektr's Opel And + 1. Maintenance instruction + 1.1 Maintenance + 2. Engine + 3. Repair of DOHC engines + 4. Repair of the diesel engine + 5. Cooling system + 6. Fuel system + 7. The fuel and exhaust system of models with system of injection of fuel + 8. Exhaust system and system of decrease in toxicity of exhaust gases + 9. Fuel systems of the diesel engine + 10. Engine electrical systems + 11. Transmission + 12. Mechanical transmission + 13. Automatic transmission + 14. Power shafts + 15. Brake system - 16. Suspension bracket 16.2. General information 16.3. Replacement of the bearing of a forward wheel 16.4. Forward lower frame 16.5. Rack of a forward suspension bracket 16.6. Lower lever of a forward suspension bracket 16.7. Replacement of plugs of the lower lever of a forward suspension bracket 16.8. Spherical hinge of the lower lever of a forward suspension bracket 16.9. Forward stabilizer of cross stability 16:10. Replacement of plugs of the forward stabilizer of a cross ustoycha of a vost 16:11. Adjustment of the bearing of a back wheel (SOHC model) 16:12. Replacement of the bearing of a back wheel (the SOHC model till 1993) 16:13. Replacement of the hug bearing of a back wheel (model since 1993) 16:14. A nave of a back wheel (model with the SOHC engine) 16:15. Back shock-absorber 16:16. Replacement of rubber elements of fastening of the back shock-absorber 16:17. Springs of a back suspension bracket (SOHC model) 16:18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines) 16:19. Back stabilizer of cross stability 16:20. Replacement of the plug of the longitudinal lever of a back suspension bracket 16:21. The fastener of a back nave (model with SOHC engines) 16:22. Check of system of the self-leveled back suspension bracket 16:23. Control system elements self-leveled a back suspension bracket 16:24. Replacement of the bearing of a back wheel (model with DOHC engines) 16:25. A nave of a back wheel (model with DOHC engines) 16:26. Knot of a back suspension bracket (model with DOHC engines) 16:27. The diagonal lever of a back suspension bracket (model with DOHC engines) 16:28. Back stabilizer of cross stability 16:29. Steering wheel 16:30. Centering of a steering wheel 16:31. Replacement of the elastic coupling of a shaft of steering transfer 16:32. Steering column 16:33. Repair of a steering column 16:34. Shock-absorber of steering transfer + 16:35. Replacement of protection covers of steering transfer 16:36. Removal of air from system of steering with the amplifier 16:37. Pump of the amplifier of steering 16:38. Popolnitelny tank of system of the amplifier of steering 16:39. Pipes of cooling of liquid of the amplifier of steering 16:40. Tips of steering draft 16:41. Steering draft 16:42. Angles of installation of forward wheels + 17. Body + 18. Electric equipment + 19. Check of malfunctions
|
Prevention
At connection трубопрово Dov it is necessary to use new sealing rings.
MODELS OF 1,6 L (TILL 1992)
Removal
Arrangement of bolts of fastening of the pump of the amplifier of steering on models of 1,6 l till 1992
PERFORMANCE ORDER |
1. Remove the case of the air filter located on the right side of a motor compartment. |
2. Take off a generator drive belt / on Sosa of the amplifier of steering. |
3. Unscrew three bolts and remove a pulley of the pump of the amplifier of steering. |
4. Release and remove an external casing of a gear belt. |
5. Disconnect pipelines from the pump and close the ends of pipelines suitable traffic jams. |
6. Unscrew two bolts and remove the pump from the block of cylinders, moving it towards the generator (see rice. An arrangement of bolts of fastening of the pump of the amplifier of steering on models of 1,6 l till 1992). |
7. At a pump exit out of operation it needs to be replaced as repair of the pump is not provided. |
|
Installation
PERFORMANCE ORDER |
1. Installation is made in the sequence, the return to removal. At connection of pipelines use new sealing rings. Establish and adjust a tension of a belt of the drive of the generator/pump of the amplifier of steering. |
2. Add liquid in system of steering and remove air from hydraulic system. |
|
MODEL 1,6 (SINCE 1993), 1,8 AND 2,0 L
Removal
Hydraulic connections of the pump of the amplifier of steering on models of 2,0 l
|
1 – connection of the pipeline;
2 – connection of a flexible hose |
PERFORMANCE ORDER |
1. Take off a belt of the drive of the pump of the amplifier of steering. |
2. Disconnect the pipeline and a flexible hose from the pump and close their ends traffic jams (see rice. Hydraulic connections of the pump of the amplifier of steering on models of 2,0 l). |
3. Unscrew four bolts and remove the pump of the amplifier of steering from the car. |
4. At a pump exit out of operation it needs to be replaced as repair of the pump is not provided. |
|
Installation
Arrangement of bolts of fastening and bolts which need to be weakened at adjustment of a tension of a driving belt on l models 1,8 and 2,0 till 1992
|
The moments of tightening of bolts And, In and With are given in technical characteristics. |
Arrangement of bolts of fastening of the pump of the amplifier of steering on models with DOHC engines
|
1 – a bolt of fastening of the pump to an arm;
2 – a bolt of fastening of the pump to an arm;
3 – a bolt of fastening of a bracket to the pump;
4 – a bolt of fastening of a bracket to the engine
|
|
|