Vektr's Opel And + 1. Maintenance instruction + 1.1 Maintenance + 2. Engine + 3. Repair of DOHC engines + 4. Repair of the diesel engine + 5. Cooling system + 6. Fuel system + 7. The fuel and exhaust system of models with system of injection of fuel + 8. Exhaust system and system of decrease in toxicity of exhaust gases + 9. Fuel systems of the diesel engine + 10. Engine electrical systems + 11. Transmission + 12. Mechanical transmission + 13. Automatic transmission + 14. Power shafts + 15. Brake system + 16. Suspension bracket - 17. Body 17.2. General information 17.3. Security measures when carrying out welding works 17.4. Care of a body 17.5. Repair of insignificant damages of a body 17.6. Repair of strong damages of a body 17.7. Cowl 17.8. Cowl lock 17.9. Cowl lock cable 17:10. Trunk lid (Sedan models) 17:11. Lock of a trunk lid (Sedan model) 17:12. Cylinder of the lock of a trunk lid (Sedan model) 17:13. Back door (Hatchback models) 17:14. Lock of a back door (Hatchback model) 17:15. Cylinder of the lock of a back door (Hatchback model) 17:16. Racks of a back door (Hatchback model) 17:17. Doors 17:18. Door upholstery 17:19. Internal handle of opening of a door 17:20. External handle of opening of a door 17:21. Door lock cylinder 17:22. Door lock 17:23. Limiter of opening of a door 17:24. Wind and back flew down 17:25. Back triangular window leaves 17:26. Door glass 17:27. Window regulators 17:28. External rear-view mirror 17:29. Bumpers 17:30. Front grille 17:31. Windshield deflector 17:32. Wheel arch inserts 17:33. Lower protective plate (mudguard) of the engine 17:34. Folding shutter of a fuel-filling mouth of the fuel tank + 17:35. Hatch elements 17:36. Finishing of an interior + 17:37. Panels of finishing of the dashboard 17:38. Central console 17:39. Ceiling 17:40. Sitting (without mechanisms of a tension of seat belts) 17:41. Seat belts 17:42. Seat belt tension mechanism 17:43. Forward sitting with the seat belt tension mechanism + 18. Electric equipment + 19. Check of malfunctions
|
FORWARD DOOR
Removal
Removal of a bracket of fastening of the handle of a window regulator
Removal of decorative finishing of the internal handle of opening of a door
Arrangement of the electric socket of the drive of a rear-view mirror in an arm on the top part of a door
PERFORMANCE ORDER |
1. Using a screw-driver edge as the lever, remove a decorative overlay of the button of blocking of the door lock, then remove the blocking button from draft of the lock. |
2. On models with manual steklopodjemn a lump completely close a window and note a window regulator handle arrangement. Release a bracket of fastening and remove the handle. The bracket is released if to insert pure fabric between the handle and an upholstery of a door and, stretching fabric opposite to the ends of a bracket, hook on a bracket and release it. At the same time it is necessary to pull the handle on himself that she after release of a bracket acted from window regulator shlits (see rice. Removal of a bracket of fastening of the handle of a window regulator). |
3. Using a screw-driver edge as the lever, remove plastic decorative finishing of the internal handle of opening of a door (see rice. Removal of decorative finishing of the internal handle of opening of a door). |
4. Unscrew seven screws at the basis of an upholstery of a door and at the basis of the handle of opening of a door/armrest. Take the bracket fixing a pocket of a door which arrange on in the lower back part of a pocket. |
5. Using the screw-driver with a wide edge, separate a door upholstery from a door. |
6. Unbend an upholstery of a door and take a big bracket in a back part of a door. |
7. On models with the electric drive of external rear-view mirrors on a door of the driver disconnect the electric socket from the mirror switch. Remove a weight wire from the accumulator, note a socket arrangement in an arm in the top part of a door and disconnect the electric socket (see rice. An arrangement of the electric socket of the drive of a rear-view mirror in an arm on the top part of a door). |
8. On models with marker lights on a door remove a bulb and disconnect the electric socket. |
9. Remove a loudspeaker and the back fixing bracket of an upholstery of a door which is attached to a door by one screw from an internal part of a door. Being careful, remove a protective film from a door. |
10. If necessary remove a pocket from a door upholstery for what unscrew three screws and release a bracket from a back part of an upholstery of a door. |
|
Installation
Installation is made in the sequence, the return to removal taking into account the next moments...
PERFORMANCE ORDER |
1. If at removal the protective film of a door was damaged, replace it as, otherwise, rain water can get into the car or damage a door upholstery. |
2. Check reliability of connection and correctness of an arrangement электричес whom the socket of the switch of provision of a mirror. |
3. If at removal of an upholstery of a door the fixing brackets were broken, replace them. |
|
BACK DOOR
Removal
Removal of an upholstery of a back door
PERFORMANCE ORDER |
1. Using a screw-driver edge as the lever, remove a decorative overlay of the button of blocking of the door lock, then remove the blocking button from draft of the lock. |
2. On models with manual steklopodjemn a lump completely close a window and note a window regulator handle arrangement. Release a bracket of fastening and remove the handle. The bracket is released if to insert pure fabric between the handle and an upholstery of a door and, stretching fabric opposite to the ends of a bracket, hook on a bracket and release it. At the same time it is necessary to pull the handle on himself that she after release of a bracket acted from window regulator shlits. |
3. Using a screw-driver edge as the lever, remove plastic decorative finishing of the internal handle of opening of a door. |
4. On models with power windows remove a weight wire from the accumulator, then, being careful, take the switch from an upholstery of a door and disconnect from it the electric socket. |
5. Unscrew three screws fixing a door upholstery. Two screws are located under finishing of the internal handle of opening of a door, and the third – an engine support arm;
5 – in the basis of the additional handle of a door. |
6. Using the screw-driver with a wide edge, separate a door upholstery from a door. |
7. Remove a door upholstery (see rice. Removal of an upholstery of a back door). |
8. Remove a protective film from a door. |
|
Installation
PERFORMANCE ORDER |
1. Installation is made in the sequence, the return to removal taking into account the next moments. |
2. If at removal the protective film of a door was damaged, replace it as, otherwise, rain water can get into the car or damage a door upholstery. |
3. Arrange a window regulator switch electrical wiring so that it did not interfere with work стеклоподъ an emnik. |
4. If at removal of an upholstery of a door the fixing brackets were broken, replace them. |
|
|
|