Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
- 17. Body
   17.2. General information
   17.3. Security measures when carrying out welding works
   17.4. Care of a body
   17.5. Repair of insignificant damages of a body
   17.6. Repair of strong damages of a body
   17.7. Cowl
   17.8. Cowl lock
   17.9. Cowl lock cable
   17:10. Trunk lid (Sedan models)
   17:11. Lock of a trunk lid (Sedan model)
   17:12. Cylinder of the lock of a trunk lid (Sedan model)
   17:13. Back door (Hatchback models)
   17:14. Lock of a back door (Hatchback model)
   17:15. Cylinder of the lock of a back door (Hatchback model)
   17:16. Racks of a back door (Hatchback model)
   17:17. Doors
   17:18. Door upholstery
   17:19. Internal handle of opening of a door
   17:20. External handle of opening of a door
   17:21. Door lock cylinder
   17:22. Door lock
   17:23. Limiter of opening of a door
   17:24. Wind and back flew down
   17:25. Back triangular window leaves
   17:26. Door glass
   17:27. Window regulators
   17:28. External rear-view mirror
   17:29. Bumpers
   17:30. Front grille
   17:31. Windshield deflector
   17:32. Wheel arch inserts
   17:33. Lower protective plate (mudguard) of the engine
   17:34. Folding shutter of a fuel-filling mouth of the fuel tank
   + 17:35. Hatch elements
   17:36. Finishing of an interior
   + 17:37. Panels of finishing of the dashboard
   17:38. Central console
   17:39. Ceiling
   17:40. Sitting (without mechanisms of a tension of seat belts)
   17:41. Seat belts
   17:42. Seat belt tension mechanism
   17:43. Forward sitting with the seat belt tension mechanism
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


17:29. Bumpers

FRONT BUMPER

Removal

Unscrewing of the right bolt of fastening of a front bumper (the air filter is removed)

Arrangement of brackets of fastening of a front bumper

PERFORMANCE ORDER
1. Remove headlights.
2. The front bumper is removed assembled with the forward decorative panel therefore on models with lobbies of a protivotumanna ми headlights disconnect electric sockets from fog lights. On models with DOHC engines and on models since 1993 remove a front grille. In the presence also remove a water reflector.
3. The front bumper fastens bolts from two parties and brackets. The right bolt of fastening can be unscrewed assembled with the air filter. If necessary remove the air filter for access to the right bolt of fastening of a bumper.
4. Unscrew the right and left bolts of fastening of a bumper from body panels behind apertures of headlights (see rice. Unscrewing of the right bolt of fastening of a front bumper).
5. Take brackets of fastening of a bumper from a body, moving a bumper forward and remove the ends of a bumper from wings (see rice. Arrangement of brackets of fastening of a front bumper).
Being careful, remove a bumper from the car.

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal.

REAR BUMPER

Removal

Removal of the back panel of finishing of a luggage carrier

Arrangement of a nut of fastening of a rear bumper

PERFORMANCE ORDER
1. For access to nuts of fastening of a bumper remove the back panel of finishing of the luggage compartment for what the screw-driver take percussion caps, then lift the panel for release it from the lower fastenings up (see rice. Removal of the back panel of finishing of a luggage carrier, Arrangement of a nut of fastening of a rear bumper).
2. The bumper is removed assembled with the lower decorative panel of finishing.
3. Remove a weight wire from the accumulator, then remove a lamp of illumination of registration plate from a bumper and disconnect the electric socket.
4. Unscrew nuts of fastening of a bumper. On models with DOHC engines of a nut of fastening of a bumper are available from under the car.
5. In the presence remove special rivets which fix both parties of a bumper to a wheel arch.
6. Remove additional brackets of fastening of a bumper which are from a reverse side of a bumper.
7. From a forward part of a bumper take clamps for what squeeze out from them the central pin.
8. Move each party of a bumper to a back part of the car, then disconnect the ends of a bumper from back wings.
9. Being careful, remove a bumper from a back part of the car, at the same time do not tear an electrical wiring of a lamp of illumination of registration plate.

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal.