Opel Vectra A

since 1988-1995 release

Repair and operation of the car



Vektr's Opel And
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Check of a compression
   2.5. Repair operations on the engine installed in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about removal of the engine
   + 2.8. Removal and installation of the engine without transmission
   + 2.9. Removal and installation of the engine together with the transmission
   2.10. Replacement of support of the engine and transmission
   2.11. Repair of the engine
   + 2.12. A gear belt and pulleys (without automatic mechanism of a tension)
   2.13. A gear belt and the mechanism of a tension (l models 1,4 and 1,6 except C16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and mechanism of a tension (l C16 NZ2 models 1,8 and 2,0)
   2.16. Forward sealing ring of the camshaft
   2.17. Back sealing ring of the camshaft
   2.18. Camshaft and case of the camshaft
   + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   + 2.21. Repair of a head of the block of cylinders
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a bent shaft
   2.26. Replacement of a back sealing ring of a bent shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a bent shaft
   2.33. Check of a bent shaft
   2.34. Survey and check of a gap in radical and conrod bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Start of the engine after capital repairs
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. The fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of decrease in toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrical systems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions


24bec775


2.10. Replacement of support of the engine and transmission

GENERAL INFORMATION

Prevention

At installation it is necessary to use new bolts of fastening of the left and right arm to a body.


The power unit fastens in a motor compartment on three support, two of which are fixed on the transmission and one on the engine.

Arrangement of bolts of fastening of the right support of the power unit

1 – fastening bolts to a body;

2 – fastening bolts to the block of cylinders


Arrangement of bolts of fastening of the left support of the power unit

1 – fastening bolts to a body;

2 – bolts of fastening of an arm to the block

Right support

PERFORMANCE ORDER
1. Tighten the emergency brake, then lift a forward part of the car and establish on supports.
2. Hook on the engine captures грузоподъ the pit mechanism and raise so that the weight of the engine was perceived by the load-lifting mechanism.
3. Working under the car, unscrew bolts of fastening of a support from the block of cylinders and a body. Take the right support of the power unit from under the car (see rice. Arrangement of bolts of fastening of the right support of the power unit).
4. Unscrew the fastening block from an arm.
5. Install the new block of fastening on an arm and fix by bolts, having tightened them the required moment.
6. Install the right support of the power unit on the block of cylinders and fix by bolts, having tightened them the required moment.
7. Fix the right support of the power unit to a body by new bolts, having tightened them the required moment.
8. Disconnect captures of the load-lifting mechanism from the engine.
9. Lower the car on the earth.

Left support

PERFORMANCE ORDER
1. Tighten the emergency brake, then lift a forward part of the car and establish on supports.
2. Hook on the engine captures грузоподъ the pit mechanism and raise so that the weight of the engine of a vosprina matsya by the load-lifting mechanism.
3. Working under the car, unscrew the fastening block from an arm and a body (see rice. Arrangement of bolts of fastening of the left support of the power unit).
4. Using a tap of M10x1,25, clear a carving in body openings for fastening of the left support of the power unit.
5. Install the new block of fastening on an arm and fix by bolts, having tightened them the required moment.
6. Fix the left support of the power unit to a body and tighten bolts the required moment.
7. Disconnect captures of the load-lifting mechanism from the engine.
8. Lower the car on the earth.

Back support

PERFORMANCE ORDER
1. Tighten the emergency brake, then lift a forward part of the car and establish on supports.
2. Hook on the engine captures грузоподъ the pit mechanism and raise so that the weight of the engine of a vosprina matsya by the load-lifting mechanism.
3. Working under the car, unscrew a back support from the lower frame and an arm.
4. Install the new block of fastening on the lower frame and an arm and fix by bolts, having tightened them the required moment.
5. Disconnect captures of the load-lifting mechanism from the engine.
6. Lower the car on the earth.